Bore Tech’s C4 Carbon Remover™ sets the standard for a high performance, cutting edge carbon cleaners that immediately begins to eliminate heavy carbon fouling without the safety hazards, harmful toxicity, and offensive odors typically found in competitive cleaners. Stubborn baked-on carbon fouling in rifle throats, AR bolt-tails and shotgun gas pistons are no match for the C4 Carbon Remover.

Bore Tech’s C4 Carbon Remover™ is a cutting edge carbon cleaner that quickly and effectively removes heavy carbon fouling without the hazards, toxicity, and odors typically found in competitive cleaners.

C4 CARBON REMOVER IS 100%

BARREL SAFENON HAZARDOUSAMMONIA FREE
ODOR FREEBIODEGRADABLEUSER FRIENDLY

 

Bore Tech C4 Carbon Remover features a highly advanced chemical formulation that begins its assault on carbon fouling by utilizing a strategic blend of chemical surfactants that quickly loosens and releases carbon deposits from the surface.

C4 Carbon Remover’s proprietary formulation utilizes a sophisticated blend of surfactants, penetrants, suspending agents and chemical action to remove stubborn carbon deposits. This enhanced formulation provides a deep clean and also effectively neutralizes and removes the corrosive residues found in surplus ammunition and black powder.

The C4 Carbon Remover is ideal for barrels, throats and chambers, AR bolt and bolt carriers, flash suppressors, compensators, revolver cylinders, gas pistons and any other place extreme carbon fouling is found.

Are your firearms Bore Tech C4 Carbon Remover clean?

Bore Tech - Redefining Gun Care
Proudly made in the USA


C4 CARBON REMOVER

Bottle TypeTreated HDPE Plastic 
Cap TypeTwist Open/Close Dispensing Cap w/ foam gasket seal
100% Barrel Safe 
Odor Free 
Non-Hazardous 
100 % Biodegradable 
Contains No Ammonia 
Short Term Rust Preventative 
Non-Flammable 

Please see our convenient and easy to use Chemical Selection Guide by clicking the below image or going to the Knowledge Center.

Chemical Selection Guide

Bore Tech C4 Carbon Remover™ Use Instructions

UNLOAD FIREARM

1) Wet 3 to 4 Bore Tech X Count patches with C4 Carbon Remover and individually push through bore to remove loose fouling. Only push patches through the bore in ONE direction.

2) Next, make 10 to 15 passes with a tight fitting Bore Tech brush saturated with C4 Carbon Remover.

3) Then repeat Step 1 and let C4 Carbon Remover soak for 5 to 10 minutes. For badly fouled rifles or parts, extended soak times may be needed.

4) Finally, push dry patches through the bore until they come out clean.

5) Repeat above steps if necessary.

6) Before storing firearm, dampen a patch with C4 Carbon Remover and push through bore. This will protect against rust/corrosion for up to 2 weeks under normal storage conditions.

7) For extended storage or in adverse conditions apply Bore Tech Friction Guard XP Gun Oil.

8) Before using firearm, always run a dry patch through the bore. This will remove any residue and ensure against obstructions.

Q: What is the difference between C4 Carbon Remover and Eliminator Bore Cleaner?

A: The C4 Carbon Remover is recommended for extreme carbon fouling situations such as AR bolt/bolt carriers, revolver cylinders or neglected barrels and specifically removes carbon fouling only. Eliminator removes both carbon and copper fouling and is recommend for most regular fouling situations. Please see our Chemical Selection Guide located in the Specification Tab or in our Knowledge Center for more information.

Q: Is C4 Carbon Remover safe to leave soak in a barrel overnight?

A: Yes, the C4 Carbon Remover can be left to safely soak in barrels for an infinite time period.

Q: Does C4 Carbon Remover contain ammonia or any other barrel damaging components?

A: No, the C4 Carbon Remover is 100% barrel safe.

Q: Is the C4 Carbon Remover safe for use on chrome lined barrels?

A: Yes, the C4 Carbon Remover can be safely used on chrome lined barrels, chromoly steel barrels, stainless steel barrels and any other commonly used barrel steel.

Q: Is the C4 Carbon Remover safe if it gets on my rifle stock?

A: The C4 Carbon Remover is safe on all polymer, fiberglass, laminated or polyurethaned wood. However, if the C4 Carbon Remover comes in contact with an oiled wooden stock, it might cause a blemish by removing the oil and require reapplication of sealing oil.

Q: Can C4 Carbon Remover be used on the outside of my rifle barrel?

A: Yes, the C4 Carbon Remover can be safely used on the outside of a rifle barrel to remove carbon fouling. Once finished cleaning be sure to wipe the cleaned area dry and apply Bore Tech Shield XP Rust Preventative.

Q: Can C4 Carbon Remover be used on nickel plating?

A: Yes, the C4 Carbon Remover can be used on nickel plating but cannot be left in contact for more than 3-5 minutes. Extended contact can lead to darkening or discoloration of the plating. Do not use on plating that has been damaged or worn.

Q: Can C4 Carbon Remover be used as a lubricant?

A: No, the C4 Carbon Remover is a cleaner not a lubricant. Use Bore Tech Friction Guard XP Gun Oil for superior lubrication.

C4 CARBON Remover 4oz - 118ml

  • Brand: Bore Tech
  • Product Code: BTCC-35004
  • Availability: In Stock
  • 17.95€

  • Ex Tax: 14.83€